Knowde Enhanced TDS
Identification & Functionality
- Fillers Included
- Polymer Name
- Technologies
Features & Benefits
- Labeling Claims
Applications & Uses
- Applications
- Compatible Polymers & Resins
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
Properties
- Color
- Mechanical Properties
- Physical Properties
- Thermal Properties
- Typical Properties
- Electrical Properties
- Flammability
- Processing Information (Injection Molding)
- Rheological Properties
| Value | Units | Test Method / Conditions | |
| Tensile Strength (Type 2) | 5.6 | MPa | ISO 37 |
| Tear Strength (Method Ba) | 30.0 | kN/m | ISO 34-1 |
| Elongation at Break (Type 2) | 375.0 | % | ISO 37 |
| Shore Hardness A (15s) | 70.0 | — | ISO 868 |
| Tensile Stress at 100% Elongation (Type 2) | 3.3 | MPa | ISO 37 |
| Value | Units | Test Method / Conditions | |
| Density | 950.0 | kg/m³ | ISO 1183 |
| Value | Units | Test Method / Conditions | |
| Coeffecient of Linear Thermal Expansion (parallel) | 10.1 | E⁻⁶/K | ISO 11359-1/-2 |
| Coeffecient of Linear Thermal Expansion (normal) | 21.8 | E⁻⁶/K | ISO 11359-1/-2 |
| Compression Set (22h, at 70°C, 25%, Type A) | 42.0 | % | ISO 815 |
| Compression Set (22h, at 100°C, 25%, Type A) | 48.0 | % | ISO 815 |
| Compression Set (72h, at 22°C, 25%, Type A) | 27.0 | % | ISO 815 |
| Compression Set (72h, at 125°C, 25%, Type A) | 61.0 | % | ISO 815 |
| Value | Units | Test Method / Conditions | |
| Service Temperature (depending on load, geometry, etc.) | - 40 to 125 | °C | — |
| Moisture Content | max. 0.1 | % | — |
| Value | Units | Test Method / Conditions | |
| Tracking Resistance (CTI) | 600.0 | — | IEC 60112 |
| Value | Units | Test Method / Conditions | |
| Flammability (1.5 mm) | HB | class | UL 94 |
| Flammability (3.0 mm) | HB | class | UL 94 |
| Glow Wire (GWFI, 650°C, 2mm) | Passed | — | DIN EN 60695 |
| Fire Behavior FMVSS (2.0 mm) | Passed | — | FMVSS 302/DIN 75200 |
| Value | Units | Test Method / Conditions | |
| Back Pressure (hydraulic) | min. 3 | bar | — |
| Mould Temperature | 10 - 60 | °C | — |
| Melt Temperature | 190 - 220 | °C | — |
| Holding Pressure (of injection pressure) | 50 - 70 | % | — |
| Injection Speed | Middle - High | — | — |
| Value | Units | Test Method / Conditions | |
| Shrinkage (Lengthwise, 24h) | 1.3 - 1.7 | % | ISO 294-4 |
| Shrinkage (Lateral, 24h) | 0.8 - 1.2 | % | ISO 294-4 |
| Spiral Flow (2 mm wall thickness) | 95.0 | cm | — |
Regulatory & Compliance
Technical Details & Test Data
- Pre-Drying Conditions
In a dry air (dessiccant) dryer 70-80 °C for 2-4 h
- Technical Data
Storage & Handling
- Storage Conditions
Store in dry, tighlty sealed protected from light not above 30°C.