Products

HALOX® CW-314 is a heavy metal-free, non-toxic, anti-corrosive pigment designed for use in waterborne and solvent-borne protective coating systems. It is particularly suitable for systems where 21 CFR 175.300 approval or compliance with ANSI or NSF standards is required. HALOX® CW-314 is highly effective in improving the infrared (IR) reflectance and thermal emissivity of elastomeric roof coatings. It enhances the total solar reflectance (TSR) while maintaining dirt pick-up resistance (DPUR) and preventing mildew growth. It can be used alone or in combination with other non-toxic corrosion inhibitors and mineral pigments in the formulation of environmentally friendly specialty paints.

HALOX® SZP-391 is a white, nonrefractive, corrosion-inhibiting pigment that is highly efficient and versatile. It is recommended for use in a wide variety of resin systems, such as alkyds (both traditional and high solids), epoxies, latexes, water-reducible alkyds, high acid value resins, catalyzed baking systems, and vinylidene chloride latexes. Its fine particle size and low oil absorption make HALOX® SZP-391 the preferred pigment for thin-film applications (<1 mil or 25 microns).

HALOX® CW-491 is a white, non-refractive, heavy metal-free pigment used as a corrosion inhibitor in protective coating systems. It is versatile and can be used with a variety of solvent and waterborne resin systems. The recommended loading levels for HALOX® CW-491 vary depending on the type of system used. For waterborne systems, the recommended loading levels range from 5–8% based on the total formula weight, while for solventborne systems, the recommended loading levels range from 7–12% based on the total formula weight.

HALOX® BW-191 is a white, non-refractive, corrosion-inhibiting pigment used in protective coating systems. It is recommended for use in most waterborne systems, such as latexes and water reducibles, and due to its lower oil absorption, it can also be effective in anticorrosive high-solids coatings. On the other hand, HALOX® BW-111 is recommended for use in solventborne epoxy systems, both conventional and high-solids.

HALOX® RC-980 is an organic additive designed to convert red rust to black iron oxide. It can be used in slightly acidic waterborne vinyl or PVDC binders applied to rusted steel substrates. It converts the rust within minutes of the coating application and forms a black iron oxide barrier that can be further top-coated with water or solvent-based paints. It does not contain tannic acid, oxime chelates, phosphates, or phosphoric acid.

HALOX® 550 is a liquid organic-inorganic sol-gel corrosion inhibitor designed for corrosion protection in thin film coatings such as water and solvent-based finishes, high gloss DTM, conventional primers, acrylic clear coats, fast-drying lacquers, wash primers, anti-fingerprint coatings, and conversion coatings. It also increases hydrophobicity and is pH stable, making it compatible with both waterborne and solventborne coatings.

HALOX® Z-PLEX 111 is a corrosion-inhibiting pigment used in protective coating systems that is highly versatile and more cost-effective than commercial zinc phosphate. HALOX® Z-PLEX 111 can provide a higher level of corrosion protection than commercial zinc phosphate when used as an equal-weight replacement.

HALOX® SW-111 is a white, nonrefractive, corrosion-inhibiting pigment used in protective coating systems. HALOX® SW-111 is recommended for use in most water-borne and solvent-borne epoxies. HALOX® SW-111 can be formulated into most water-reducible resin systems and corrosion-resistant caulks and sealants.

HALOX® SZP-391 JM is an efficient and versatile corrosion-inhibiting pigment. It is a white, nonrefractive, corrosion-inhibiting pigment used in protective coating systems. HALOX® SZP-391 JM is equally effective in such resins as alkyds (both traditional and high solids), epoxies, latexes, water-reducible alkyds, high acid value resins, catalyzed baking systems, and vinylidene chloride-based latexes and is recommended for use in a wide variety of resin systems.

HALOX® 570 is an organic corrosion inhibitor designed for use in waterborne industrial and decorative coatings to provide flash rust and long-term corrosion protection on metal surfaces. HALOX® 570 is especially effective along weld seams and, in some cases, can also be used in solvent-based coatings and UV-cured systems. HALOX® 570 may be used in formulations based on waterborne acrylic latexes and co-polymers, styrene/acrylic latexes, acrylate epoxy esters, 2-pack epoxy systems, alkyds, alkyd/acrylic blends, and 1 or 2-pack polyurethane. HALOX® 570 may be used in both waterborne primers and direct-to-metal topcoats. In direct-to-metal coatings, HALOX® 570 has a minimal effect on gloss reduction.

HALOX® Z-PLEX® 250 is a white, non-refractive, corrosion-inhibiting pigment used in various protective coatings. It is classified as Zn3(PO4)2.2H2O (dihydrate) and is compliant with ASTM D6280, Specification for Zinc Phosphate Pigment Type I. The recommended loading levels for HALOX® Z-PLEX® 250 range from 5–10% based on the total formula weight.

HALOX® 650 is an organic corrosion inhibitor primarily designed for coatings and primers on metal surfaces. It is specifically formulated for use in solvent-borne or powder-coating applications to provide long-term corrosion protection. HALOX® 650 can be used in a variety of applications, including coil coatings, resins such as thermoplastic acrylics or epoxies, powder coating systems such as polyester or TGIC, acid-catalyzed thermosetting systems such as melamine or urea-formaldehyde, and wash (etch) primers based on PVB.

HALOX® 630 is a liquid organic corrosion inhibitor for solvent-borne protective coatings on metal surfaces. It may be used in solventborne clear or pigmented coatings and in systems such as 2-pack epoxy systems, high-solids epoxy esters, alkyds, acrylic resins, and 2 pack polyurethane primers. However, in bake systems, the temperature should not exceed 150°C. It should be noted that yellowing may be observed with reactive isocyanates. HALOX® 630 provides superior corrosion resistance even over poorly prepared surfaces, such as adherent rust or oil contamination.

HALOX® 430 is a non-toxic, heavy metal-free anticorrosive pigment designed for use in waterborne and solventborne protective coating systems. HALOX® 430 is based on a unique synergy between an ion scavenging and passivation mechanism. It is recommended for use in long-term applications where the use of heavy metals, such as zinc, strontium, barium, molybdenum, and chromate, is of concern.

HALOX® Z-PLEX® 750 is an inorganic and organic hybrid corrosion inhibitor primarily designed for coatings and primers on metal surfaces. HALOX® Z-PLEX® 750 is specifically designed for use in a variety of solventborne or waterborne applications to cost-effectively provide the traditional function of an inorganic corrosion inhibitor with the benefits of an organic corrosion inhibitor.

HALOX® BW-111 is a white, non-refractive pigment used as a corrosion inhibitor in protective coating systems. It is specifically recommended for use in solvent-borne epoxy systems, including both conventional and high-solids coatings. The recommended loading levels for HALOX® BW-111 range from 5–10% based on the total formula weight for conventional systems and from 10–20% based on the total formula weight for higher solids systems.

HALOX® BW-100 is a white, nonrefractive, tannin stain-inhibiting pigment used in protective coating systems and has been specifically designed as a tannin stain inhibitor, providing performance and compatibility in a variety of resin systems such as acrylic latexes, vinyl acrylic latexes, styrenated acrylic latexes, and solventborne alkyds.

HALOX® CZ-170 is a versatile pigment used in protective coating systems to inhibit corrosion and tannin staining. It is a great replacement for zinc oxide and can be used in high-gloss and thin-film applications due to its finer particle size and narrow distribution. With a gloss of over 75 units at 60° and a film thickness of less than 1.0 mils, or 25 microns, HALOX® CZ-170 is a great option for a variety of coating needs. It can be used to protect both metal and wood substrates, making it a universal option for coating systems.

HALOX® Zinc Phosphate is a white, non-refractive, corrosion-inhibiting pigment that is widely used in protective coating systems. It is also known as zinc phosphate-dihydrate and is characterized by a narrow particle size distribution, with an upper particle size limit of 10 microns and a mean particle size of 5 microns. This pigment is highly versatile and serves as a standard corrosion inhibitor for most high-performance resin systems, including vinyl, chlorinated rubbers, and epoxies. It is especially recommended for high acid-value resins, catalyzed baking systems, and vinylidene chloride latexes. In addition, HALOX® Zinc Phosphate is an ideal choice for thin film applications (less than 1 mil or 25 microns). It meets the ASTM D 6280-98 specification for zinc phosphate pigment type I and is widely used in the industry.

HALOX® 550 WF is a water-free (WF) corrosion inhibitor and adhesion promoter that uses a sol-gel-based formula. It is designed to protect a variety of coatings, including waterborne and solventborne clear coats, glossy direct-to-metal coatings, thin-film coatings, acrylic emulsions, polyurethanes, epoxies, alkyds, water-reducible alkyds, PVB wash primers, and polyester resins. This product is suitable for use in low-pH and acid-catalyzed systems.

HALOX® 430 JM is a non-toxic, heavy metal-free anti-corrosive pigment designed for use in waterborne and solventborne protective coating systems. HALOX® 430 JM is based on a unique synergy between an ion scavenging and passivation mechanism. It is recommended for use in long-term applications where the use of heavy metals, such as zinc, strontium, barium, molybdenum, and chromate, is of concern.

HALOX® 700 is a white, non-refractive, corrosion-inhibiting pigment used in protective coatings. It provides extended protection in solvent-based and water-based epoxy and urethane coatings through the combination of zinc and aluminum phosphates. When used in alkyd and acrylic coatings, it is recommended to use it in combination with HALOX® Organic Corrosion Inhibitors for optimal performance.