Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
Applications & Uses
- Markets
- Applications
- Application Area
- Compatible Substrates & Surfaces
- Cure Method
- Applications
- ELASTOSIL® - Ready-to-Use Construction Sealants
- Sealants
- Silicone Sealants
- Application Details
Application Fields
- Sealing of low stress connection and expansion joints in the building industry
- Sealing of joints in sanitary applications
- Sealing of low stress perimeter joints
Processing
- The substrate areas that will be in contact with the sealant must be clean, dry and free of all loose material such as dust, dirt, rust, oil and other contaminants. Non-porous substrates should be cleaned with a solvent and a clean, lint-free, cotton cloth. Remove residual solvent before it evaporates with a fresh clean, dry cloth.
- It is the responsibility of the user to test the compatibility of the sealant with the adjoining materials. Incompatible substances like coating materials (paints, varnishes and glazes) or organic plasticizer containing rubbers (EPDM, butyl and neoprene) can lead to discoloration or other impairments like loss of adhesion of the sealant.
- Materials in direct contact with the applied sealant like cleaning agents and materials in indirect contact like gaseous emissions can damage the sealant in its function or change its appearance.
- Because of the multitude of these materials, Wacker cannot make a general statement to the compatibility of materials with the sealant. In case of doubt the user shall conduct appropriate preliminary tests. The time until complete curing may be extended at lower temperature, lower humidity, increasing film thickness or by low volume of air exchange.
Adhesion
ELASTOSIL® 9100 P exhibits good primerless adhesion to most of the substrates used in DIY-applications, e.g. glass, tiles, ceramics, enamel, glazed tiles and clinker, metals e.g. aluminum, steel, zinc or copper. Users must carry out their own tests due to the great variety of substances. The adhesion can be improved in many cases by pretreatment of the substrates with a primer.
Properties
- Cured Properties
Value Units Test Method / Conditions Elongation (at break) 250 % ISO 8339-A Modulus (at 100 % elongation) 0.37 N/mm² ISO 8339-A Movement Capability 20 % ISO 11600 Shore Hardness A 24 - ISO 868 Tear Strength 3 N/mm ISO 34, Method C Tensile Strength 0.5 N/mm² ISO 8339-A - Uncured Properties
Value Units Test Method / Conditions Consistency (at 23°C) Non-sag - ISO 7390, Profile U 20 Curing Rate (at 23°C, 50% r.h) 2 mm/day - Density (at 23°C) 1 g/cm³ ISO 1183-1 A Extrusion Mass Flow Rate (at 6 bar, 23°C) 400 g/min - Skin Formating Time (at 23°C, 50% r.h) 25 minutes - - Properties
- Suitable for use in sanitary areas
- Long shelf life
- Primerless adhesion to most materials
- Non-corrosive to metals
- Suitable for alkaline substrates such as concrete, mortar, fibrous cement
- Non-sag
- Ready gunnability at low (+5 °C) and high (+40 °C) temperatures
- Rapid crosslinking: quickly becomes tack-free
- Flexible at low (-40 °C) and high temperatures (+120 °C)
- Good weatherability
Regulatory & Compliance
- Certifications & Compliance
- Chemical Inventories
- Quality Standards
- Restrictions in Use
- ELASTOSIL® 9100 P must not be used as a sealant in insulating glass units.
- ELASTOSIL® 9100 P must not be used for structural glazing bonding.
- ELASTOSIL® 9100 P is not suitable for use on natural stones, such as marble, granite, quartzite, as it can cause staining.
- ELASTOSIL® 9100 P is not recommended for sealing of aquaria or for the longer-term use under water.
- ELASTOSIL® 9100 P is not suitable for food contact applications.
- ELASTOSIL® 9100 P is not suitable for use as a mirror adhesive.
Safety & Health
- Safety Note
- During vulcanization ethanol is released. These vapors should not be inhaled for long periods or in high concentration. Hence, good ventilation of the work place is necessary.
- Should unvulcanized RTV-1 silicone rubber come into contact with eyes or mucous membranes, the affected area must be rinsed thoroughly with water as irritation will otherwise be caused. Cured silicone rubber, however, can be handled without any risk to health. Keep away from children.
Packaging & Availability
- Country Availability
- Regional Availability