Knowde Enhanced TDS
Identification & Functionality
- Additives Included
- Base Oil Type
- Chemical Family
- Chemical Name
- Product Type
- Cleaning Ingredients Functions
- Industrial Additives Functions
- Plastics & Elastomers Functions
- CAS No.
- 9006-65-9
- EC No.
- 618-433-4
- Product Families
- Chemical Structure
Features & Benefits
- Labeling Claims
- HII Features
- Industrial Additives Features
- Materials Features
- Ready-to-Use Product Features
- Specific Features
- Electrically insulating
- Emulsifying
Applications & Uses
- Markets
- Applications
- Home Care Applications
- Applications
For typical application fields of VINNAPAS® 5005 N, refer to the section "application". We recommend VINNAPAS® 5005 N in tile adhesives in a dosage of up to 2%.
Processing
For the production of ready-mixed dry mortars, such as adhesives and patching compounds, blend VINNAPAS® 5005 N with the other dry ingredients in appropriate equipment. Temperatures should not be allowed to rise excessively during mixing because otherwise the dispersible polymer powder could agglomerate by virtue of its thermoplastic properties. The mortar is prepared for use by adding the recommended amount of water and mixing mechanically or by hand. Since hand mixing generates little shear force, we recommend allowing the fresh mortar to slake for 5 minutes and then stirring it again. This is usually unnecessary where mechanical mixers are employed.
- Application Details
- Due to WACKER® AK 200 many diverse applications, no general processing information can be provided. Parameters will vary from application to application.
- Available in a range of viscosities, WACKER® SILICONE FLUIDS AK are miscible with each other in any ratio. The standard product's viscosity can thus be altered to suit your individual needs.
- WACKER® AK 200 is a non-polar liquid and is immiscible with polar solvents such as water or short-chain alcohols.
- In aliphatic and aromatic hydrocarbons, chlorohydrocarbons, ethers, esters, ketones and higher alcohols, WACKER® AK 200 is soluble in any proportion.
- Before the product is used with solvents for the first time, it is advisable to perform a lab-scale test.
- When solvents are used, please remember to read the appropriate hazard information.
- Release agent
- Lubricant
- Hydraulic fluid
- Antifoam agent
- Water-repellent agent
- Liquid dielectric for electrical and electronic equipment
- Heat-transfer oil
- Polish additive
- Plastics additive
- Additive for textile and fiber auxiliaries
- For pharmaceutical applications, we recommend specialty silicone fluids from our SILFAR® line.
- Silicone fluids from our BELSIL® line are available for the cosmetic sector.
- Whenever particularly high heat and shear resistance is required, we recommend silicone fluids from our AK stab, AK visc and AKC product lines.
- Specialty grades of the product (available as WACKER® PLASTICIZER) will be needed for use as a silicone plasticizer in RTV-1 sealants.
Properties
- Color
- Physical Form
- Appearance
- Clear colorless liquid
- Typical Properties
- Properties
- Minimal change in physical properties over a broad temperature range
- Excellent water-repellent properties
- Good dielectric properties
- Low surface tension and thus high surface activity
- Chemically highly unreactive
- Low solidifying point
- High flash point
- High heat resistance
- Good solubility in a wide range of solvents
| Value | Units | Test Method / Conditions | |
| Density (at 25°C) | approx. 0.97 | g/cm³ | DIN 51757 |
| Flash Point | min. 300 | °C | ISO 2592 |
| Ignition Temperature | 450 | °C | DIN 51794 |
| Kinematic Viscosity (at 25°C) | approx. 200 | mm²/s | DIN 53019 |
| Refractive Index (at 25°C) | approx. 1.403 | — | DIN 51423 |
| Surface Tension (at 25°C) | 0.021 | N/m | — |
Regulatory & Compliance
- Certifications & Compliance
Packaging & Availability
- Country Availability
- Regional Availability
- Packaging Information
- Maximum temperature allowed during storage and transportation: 50°C
- Storage beyond the date specified on the label does not necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons.